Mace MVC-PTZ-23X Installationsanleitung

Quick Installation Guide5101 NW 21st Ave, Suite 210 • Fort Lauderdale, FL 33309www.mace.com • (877) 585-6223MVC-PTZ-23XIndoor/Outdoor 23× PTZ Speed Do

10 Figure 1-5 Note The video port is covered the heat shrink tube of high shrinking ratio. After the video connection, please heat the tube to make s

11 Figure 1-6 Important After the installation, please make sure: z The three stainless screws of the quick installation port are firmly secure. z

12The default setup is: z Address: 1 z Baud rate: 9600 1.4 Dial Switch Setup The two dial switches of the speed dome are SW1 and SW2. These are t

13ON ON 1200bps Please refer to the parity setup sheet for detailed information. 7 8 Parity OFF OFF NONE ON OFF EVEN OFF ON ODD ON ON NONE 1.4.

142 BRACKET DIMENSIONS 2.1 Wall mount bracket The wall mount bracket dimensions are shown as below. See Figure 2-1. Figure 2-1 2.2 Hanging mou

152.3 Corner mount bracket The corner mount bracket is shown as below. See Figure 2-3. Figure 2-3 2.4 Pole mount bracket The corner mount bracke

163 WALL MOUNT BRACKET INSTALLATION 3.1 Component Installation Wall mount bracket is shown as below. See Figure 3-1. Figure 3-1 3.2 Installatio

17Install the speed dome in the bracket. See Figure 3-3. Figure 3-3 Please refer to chapter 1.2 for detailed installation information.

184 HANG MOUNT BRACKET INSTALLATION 4.1 Component Installation Hang mount bracket and its components are shown as below. See Figure 4-1. Figure

19Pull the cable through the steeve and then secure the steeve to the flange. Fix the M4 bolt. Please note, if the speed dome is installed in the ou

2Table of Contents 1 QUICK INSTALLATION SPEED DOME INSTALLATION ... 7 1.1 Installation Preparation ...

205 CORNER MOUNT BRACKET INSTALLATION 5.1 Component Installation Corner mount bracket and its components are shown as below. See Figure 5-1. Fig

21 Figure 5-3 Please refer to chapter 1.2 for detailed installation information.

226 POLE MOUNT BRACKET INSTALLATION Pole mount bracket and its components are shown as below. See Figure 6-1. Figure 6-1 6.1 Installation 6.1.1

23 Figure 6-3 After you installed bracket and external cover, loosen the captive screws and open the panel, pull the power cable through the

247 APPENDIX Ⅰ THUNDER PROOF AND SURGE PROTECTION This series speed dome adopts TVS lighting protection technology. It can effectively prevent damag

258 APPENDIX Ⅱ ABOUT RS485 BUS 8.1 RS485 Bus Main Feature RS485 is semi duplex communication cable of impedance 120Ω. Its max load amount is 32 e

26 Figure 8-2 8.4 RS485 Bus FAQ Phenomenon Possible Reasons Solution Speed dome can run self-diagnosis but I can not control it. z Host address

34 HANG MOUNT BRACKET INSTALLATION ... 18 4.1 Component Installation ...

4Welcome Thank you for purchasing our speed dome! Please read the following safeguards and warnings carefully before you install or use the product!

5Important Safeguards and Warnings Safety Measures Qualified Engineer Needed z The installation engineer or maintenance engineer shall have corre

6z We are not liable for any problems caused by unauthorized modifications or attempted repair. Do not allow other object falling into the device

71 QUICK INSTALLATION SPEED DOME INSTALLATION 1.1 Installation Preparation Basic Requirement z All installation and operation here should confor

81.2 Installation Please note the quick installation speed dome includes the quick installation high speed dome, IP quick installation speed dome,

91.2.2 Install the transparent cover First, you need to check the steel wire of the bracket is firmly secure or not. Please line up the captive sc